About This

Just about every person will have their own perception on the subject of Tools You Need to Install a New Bathtub .

Setting up a bathtub isn't precisely rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging job. If the old tub is conveniently easily accessible, the task can relocate immediately; if you need to open up a wall to get rid of the old bathtub and also place the new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as embeded in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. Instead of employing a professional to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This short article will certainly aid you set up a brand-new bathtub in your bathroom if you have actually currently bought a new bathtub and also don't require to change the setup of your previous water supply pipes.
Your tools as well as product checklist must consist of the following:

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Getting ready for the Setup

First of all, the supporting framework provided with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its final placement.

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

Mounting the Tub

Using the two wood boards under its feet, place the tub in the called for placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the level reads level.
To set up faucets, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system as well as inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill up the bathtub as well as also check the overflow outlet and the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has actually been utilized a minimum of when as this will settle it right into its final setting.

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type should be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.

Tiling Around the Bath tub

In the location where the bathroom fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, creating the water to penetrate the wall surface between the bath and also the tiling, bring about issues with moisture and feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.

How to Install a Freestanding Bathtub?

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

 

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

Slope

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

Placement

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

 

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

Clean the bathroom floor

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

Steps to Install a Freestanding Bathtub:

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

 

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

 

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

 

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

 

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

 

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

Tips to Maintain a Freestanding Bathtub:

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

As a keen person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that piece of content was really helpful. Kindly take a moment to promote this blog posting if you appreciated it. Thank you so much for your time invested reading it.

Get A Free Estimate